Advertisements:




Emachine C1904 Cpu Fan Stops Working After 10 Seconds


I have a friends emachine c1904. I found the problem to the computer, it was the power supply and memory that werent working. I bought a new power supply and i used my memory stick and the computer booted right up. I scanned the computer for adware and viruses and i found a couple of minor things in there that i already erased. I went to check on the computer once again and now when i turn it on the computer the fan to the cpu goes on for like 10 seconds and stops working after that. Has anyone accured to this problem before.

View Full Post With 7 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.


Computers Keyboard Stops Working After About 10 Seconds

Does anyone know why my computers keyboard stops working after about 10 seconds when i turn it on. I've just thrown the thing togeather and i have to edit all the bios settings etc, but i can't access the bios if the keyboard dies.

Posted On: 24-08-2005, 07:04 AM . View Related Posts . . View 7 Replies .

Logitech Cordless Mouse Stops Working After 30 Seconds

Logitech cordless mouse stops working after 30 seconds and the batteries are fine. Reboot is needed and it works again for about 30 seconds. Any idea how to troubleshoot this?

Posted On: 06-12-2009, 02:08 PM . View Related Posts . . View 2 Replies .

Power Supply Fan Working, But Cpu Fan Is Not

I can not get the pc to boot. I turn on the power button, and the monitor does not get a signal. (Btw on board video & sound) i opened up the case to see that the power supply is spinning fine, however the cpu fan is not spinning at all. The heat sink was not hot to the touch however i did not have the pc plugged in for very long. I don't know much but i read somewhere i can check the power supply by plugging in an external fan to the power supply lead. So i did that, in fact the external fan worked fine. Also i must state that i do not get any thing on the monitor, only black, no beeps, no indication of post what so ever after i hit the power button. I have attempted to reset ram, and make sure all leads and cables were snug. How do i further troubleshoot? Can i rule out the power supply? Is it the mobo that has the issue? Or maybe the cpu? So to recap, power supply spins, power light on front of system lights up, no beeps upon boot up, cpu fan is dead and not spinnig. Any help would greatly be appreciated. Let me know if you need any other information.

Posted On: December 14th, 2004, 11:02 PM . View Related Posts . . View 3 Replies .

Quiet Cpu Fan

Just like the title says, my cpu fan does a good job, as it is temperature reactive to increase rpm. But the sob is soooo damn loud. Anyone recommend me (personal experience preferred) a great cpu fan (80-92mm) fan with blue leds?

Posted On: 07-01-2006, 10:03 PM . View Related Posts . . View 8 Replies .

Cpu Fan Missing

Ibm intellistation 6217-46y, i am getting a repeat error in my post error logs that says: "cpu1 fan stalled/missing". I have updated to the lates bios level. I have set the fan speed to "intelligent", (as opposed to "always full speed") but they never stop running at full. They are definitely running. Does anyone have one of these machines? There are 2 fan sockets on the motherboard, plus one on the 2nd processor board. The second socket on the main motherboard is not used - or at least i don't have anything to put on it. Can somene verify if i'm missing some hardware?

Posted On: September 25th, 2006, 05:56 PM . View Related Posts . . View 4 Replies .

Cpu Fan Error

Just finished installing my new system. I am having an error msg saying "cpu fan error! Press f1 to resume" i have fan controller installed that is connected to the 3 top of my fans and the 4th controls the cpu fan (ultra kaze 2000). The remaining 3 fans i have connected to the motherboard. According to the manual i have fans b, c, e occupied (a, d is not used, d is the cpu 4 pin fan if that helps). All of my fans are working, cant place my finger on this error. Mobo = p6t v2 deluxe

Posted On: 09-19-2009, 01:49 AM . View Related Posts . . View 7 Replies .

Error: Cpu Fan Is Not Working

I just installed a used hdt-s963 i bought off a tpu member and every time i boot i get that message and my computer shuts down. It will work if i flick the psu switch off then back on again. Reinstalled the stock hsf and did not have this problem. Would you guys think it's the fan on the 963?

Posted On: 06-17-2009, 07:50 PM . View Related Posts . . View 24 Replies .

Warning: Cpu Fan Is Low

While booting i a message shows saying "warning! Cpu fan is low", anyone knows what causes it and solutions for it.

Posted On: June 12th, 2005, 08:39 PM . View Related Posts . . View 2 Replies .

Laptop ( Cpu ) Fan Gets Really Loud

Bought this laptop about 9 months ago, and itís been perfect until recently. Every now and then, when i power up, the cpu fan goes crazy (i think itís the cpu fan ?). It gets really loud and stuff during the bios checks and stays loud. When i eventually get into windows, the applications in startup take ages to load, and some donít load at all, because one gets stuck or something. Itís really weird. Everything goes back to normal on the first or second reboot.

Posted On: May 27th, 2007, 04:04 AM . View Related Posts . . View 10 Replies .

Cpu Fan Error Warning

On boot-up i get beeps with an " cpu fan error" & have to click on "f1" to continuous booting. "Real temp" shows 30c instead of 23-25 degsc it used to show. I reinserted the fan cable & fan spins freely. Any ideas about this?

Posted On: February 16th 2009 . View Related Posts . . View 4 Replies .

Dell Inspiron 6000 Cpu Fan Always On

I have a dell inspiron 6000 with vista ultimate installed on it. I recently noticed that while the pc is up, the cooling fan (or the cpu fan?) Is on about 80% of the time, even when the cpu is at 2 or 3%. Sometimes, i see this even when the cpu is 0%. Does anyone have any idea on what may be going on here?

Posted On: 30-11-2007, 12:10 AM . View Related Posts . . View 4 Replies .

Replacing The Cpu Fan In A Sentia 223

It seems like it's going to run me $80+ to get this part (exact replacement). The fan is a bi-sonic dc 5v 0. 28a cpu fan. The model number is bp38085h (or something to that effect). The fan is a 2 wire (red and black) but a 3 pin connector (middle pin is empty). Can i get a working replacement at a cheaper cost? Spending $100 on a free, older laptop doesn't seem worthwhile.

Posted On: October 11th, 2008, 12:30 AM . View Related Posts . . View 0 Replies .

Can I Clean My Cpu Fan ,as It Fill With Dust ?

Can i clean my cpu fan , as there is too much dust is fill in it? And if yes so how can i clean it without any harm.

Posted On: December 14th, 2008, 03:02 PM . View Related Posts . . View 4 Replies .

Is Thermal Paste Necessary Between Cpu And Fan Cooler ?

Is it necessary to use the refrigerant cream (don't know the actual name), between the cpu and its fan cooler? Is it necessary? Cause i saw once that a guy put this cream, but now i have my unassembled pc and don't see this cream, so i must buy it or it's not necessary to put it.

Posted On: 3 weeks ago . View Related Posts . . View 5 Replies .

Cpu Fan Starts To Spin For A Split Second And Then Cuts Out

I just put together a new workstation, and when i press the power button on the front of the case, the cpu fan starts to spin for a split second and then cuts out and nothing else happens, no beeps, no post, nothing. Bad power supply or is something hooked up incorrectly?

Posted On: March 25th, 2006, 11:58 AM . View Related Posts . . View 4 Replies .

Asus A8r32-mvp Deluxe, Cpu Fan Error

Basically i got a "cpu fan error!" Message every time i started my computer. My fan speed was good, a bit over 3000 rpm, so i just bypassed it and kept using my computer as usual. After a while the motherboard would beep sometimes and the computer would freeze for a few seconds. This happened more and more often until sometimes it would do that nonstop and i had to turn the computer off by holding the power button. So i go into the bios and disabled the fan speed monitoring. That doesn't help, i still get the cpu fan error message. Here's where it gets interesting: after much fiddling around with the settings and bios and whatnot, it still gets the cpu fan error but now it seems to be unable to detect my operating system (windows xp). It goes through the startup procedure and after the mobo screen it displays "reboot and select proper boot device or insert boot media in selected boot device and press a key. " The primary boot device is the hard drive, which used to have no problem starting up as early as this afternoon. (On another note, the cpu fan error seems to have stopped)

I just would like some suggestions as to what is going on and how i can fix this. I'm pretty sure i destroyed my os and will need to reformat or something equally silly. (By the way, i tried putting the windows cd in the drive and booting from that and selecting repair the os. It gave some error about not finding an os to repair. If you think it helps i can go and get that error text again. )


Posted On: 12-14-2007, 06:13 AM . View Related Posts . . View 5 Replies .

No Power Up But Mobo Light On, Cpu Fan Spins Briefly

I have a fairly old d915pbl motherboard that i've been using for years. I was using it until i wanted to debug a graphics problem on a different system. I took the graphics card out of the 915 for about an hour. When i returned it the system wouldn't boot. I took out the graphics card and it still wouldn't boot. The onboard led lights up (green) and the cpu fan spins for about 1 second. The onboard light stays on, but the front pannel light never goes on. I was initially worried that the psu died, so i tried a different psu on the 915 motherboard and the results were the same. I still felt that i hadn't eliminated the original psu as the problem so i used the original psu on a different system and the other system powered up fine, so the psu is good. Then i got worried about the front pannel "sw power" connector so i took another system and set it up next to the 915. I plugged the two-pin "sw power" cable from the new system into the 915 and attempted to use the new system's power button. This didn't help either. I'm not entirely sure this test was valid, so i tried the "short the power pins" trick and pressed a screwdriver against the two "sw power" pins, no luck, no power on. I'd like to buy a little power switch to see if that makes a difference, but i'm doubtful. I'm not sure what to do now other than assume the system is fried and upgrade the mobo/proc. I'm also not sure about the cmos battery. This could be a problem, but i read that ususally the bios will post and then complain about the cmos battery. I don't know how true that is though. Any suggestions would be appreciated before i replace the system.

Posted On: 10-27-2009 . View Related Posts . . View 12 Replies .

Arctic Cooling Freezer 7 Pro Cpu Fan Spinning Intermittently

My arctic cooling freezer 7 pro cpu fan is only spinning intermittently on my asus motherboard. I have an asus p5n-sli-e. The fan is plugged into my motherboard by the 'cpu' power socket (4 pin, not molex). The cpu power socket it plugs into works - as i was running another cpu fan on it just fine, and occasionally it will spin up for a few seconds but never any longer. Cant use this pc very much as obviously the cpu overheats which crashes the pc.

Posted On: 2 months ago . View Related Posts . . View 1 Replies .

Drivers For Emachine C3060

I did a fresh windows xp install on my friends computer. This is my first time working on an emachine computer. Do you guys know where i can get the drivers for this computer? After i did a fresh install i noticed that this had a recover partition (pc angel). I am not sure i can the drivers from this partion or if they are avaialble online.

Posted On: July 19th, 2008, 10:56 PM . View Related Posts . . View 11 Replies .

Emachine - No Boot Disk

I've been working on this old emachine for a woman down the street and i finally got it running but it's acting a bit strange. She called me up today and said it tells her she has "no boot disk". Now, i know i was just there and had windows xp boot up. So i go there, turn it on. And boot up normally. So i make sure everything else is working. I turned it off and on a few times, everything was normal. I left and an hour later she calls me back. "It's a black screen that says "no boot disk" on it". She says she didn't turn it of/restart or anything. I'm trying to get a handle on what's wrong here. I can't get a handle on it because i'm never there when something goes wrong. It's a 3100+ sempron with 256 mb ram and a 100gb ide hdd. Integrated sound, network, and graphics (chrome s3 i think). Any ideas? Is it possible that her psu is shutting down and resetting her boot settings? I'm sure the hard drive has a recovery partition (but that should also be bootable). Maybe her psu and the motherboard batter are both hosed. I don't know anymore lol. Any ideas are appreciated.

Posted On: 06-13-2009, 02:22 PM . View Related Posts . . View 4 Replies .

Emachine - Power Led Only Flashes

Alright, i have an emachine here that will not power on. When power is hooked up to the psu the light around the button just sits and flashes. The psu fan will run but no beeps, hard drive spin up or cpu fan spinning. I have tried multiple psus and i'm guessing that the mobo is dead but what are some of your thoughts?

Posted On: 06-12-2008, 11:39 PM . View Related Posts . . View 9 Replies .

Emachine 400i3 Dvd Issue

I just received my 2 disc drives. One is a dvd|toshiba 16x sd-m2012, and the other is an cdrw/dvd asus| cb-5216a. To tell the truth, i only bought the toshiba for the dvd capabilities, and the asus for burning, and know little of the two. I know both play dvd's though. The problem i have is this, i have an old e-machine 400i3 and i am keeping the drives in it until i can get my other computer built. I wanted to check out the whole 52x speed and all, but all i can run is 16x on a cdrw, when the specs show that 32x is capable. Is it because of my old computer? Or may there be something wrong, otherwise? Oh, and the sound does not work when i play a dvd, yet, if i play music, its fine.

Posted On: December 9th 2005 . View Related Posts . . View 11 Replies .

Connect Emachine Desktop To Flat Screen Tv

How do i connect my emachine desktop to my flat screen tv? I am connecting the cable from the emachine's tower to the vga port behind the tv, but am getting an error on the tv saying that it is not a supported format. How do i fix this problem? If you need more information let me know.

Posted On: 3 months ago . View Related Posts . . View 2 Replies .

Sapphire Radeon Hd 4850 - Emachine Et1331-02

My computer only has one visible power slot for a graphics card with two connectors? My computer model is an emachine et1331-02. As i've already had enough trouble breaking open the back of the case's metal slots (problem described here: http://www.Tomshardware.com/forum/284059-33-cant-insert-video-card-emachine), now another problem arises. I'm only 14, and i don't know too much about computers themselves. I recently got this new graphics card to enhance my computer, a sapphire radeon hd 4850, and its power connector has two individual slots, and in my machine, i can only see one visible slot to plug it in. Do i need both to power the card? If not, which one do i use (one has 3 wires connected and the other has 5)? And if i do need both. I only have one slot.

Posted On: 4 weeks ago . View Related Posts . . View 1 Replies .

Uninstall Cpu Drivers When Installing New Cpu ?

Do i need to uninstall the cpus ''drivers'' in the control panel? Or just switch it with out doing anything?. Switching to a q6600 soon from my intel c2d e4400 2. 0ghz.

Posted On: 01-19-2008, 10:15 PM . View Related Posts . . View 24 Replies .

Intel Cpu Or Amd Cpu For Notebook ?

I am looking for laptop now, i am trying to save some money, and i found out the amd turion cpu is cheaper than intel's, does anyone know what's the different? Which one is better? And which one save more power?

Posted On: July 25th 2007 . View Related Posts . . View 2 Replies .

Pc Goes Off In About 2 Seconds

Right so i put together my second machine (for a friend this time), plugged everything in to the best of my ability, and pressed the power button. The lights come on, the fans start spinning, then it all goes off in a matter of about 2 seconds. Can anyone evaluate what this problem could be caused by?

Posted On: 04-19-2007, 07:32 PM . View Related Posts . . View 8 Replies .

Pc Boots To Xp Logo Then Stops

I replaced by power supply. Now i get the beep and the xp logo but no signal. I have check the power supply to make sure its connected correct. I have reseated the video card and the drive cables. I checked and reseated the memmory. I have tested the monitor on another system.

Posted On: February 28th, 2006, 01:11 PM . View Related Posts . . View 3 Replies .

Power Shuts Off After Just 3 Seconds

I have just put together a new computer, the second one i have ever built, and when i go to start it up for the first time the power stays on for about 3-4 seconds and then suddenly cuts out, like it got unplugged. I flipped the power switch a few times and got no response. If i count ten seconds, flip the switch again, it will turn on but again only for 3-4 seconds. There are no beeps either. Everything in it is new, a new amd mobo from ecs "kt600-a", a new 1. 6ghz amd duron processor, new radeon 9200 256mb video card, new powermax 400watt power supply. I tried clearing the cmos, but still no change. I have all the jumpers set right as far as the cpu frequency goes, but i have no idea what it could be. I hope its not a bad mobo, because i got it from newegg.com and i can only return it for the same make and model. Any ideas?

Posted On: September 4th, 2004, 04:22 PM . View Related Posts . . View 6 Replies .