Hp Pavilion Dv6000 Wireless Network Only Local Access

Hp pavilion dv 6000 only gives local access to my wireless network. Excellent signal and connects via ethernet. Another hp computer and 3 i phones have no problem at all. The main computer is on windows 7 and the laptop on vista. Would this have anything to do with it?

View Full Post With 2 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.

Hp Dv6000 Pavillion Laptop Wireless Network Adapter Issue

I have a hp dv6000 pavillion laptop. It has a built in wireless network card. For some reason, in the past few weeks, the card does not enable itself when i start my computer. The switch on my computer is switched to enabled but the computer acts like nothing is there. I can slide the bar that enables the wireless from disable to enable all i want but nothing happens. But after i restart my laptop a bunch of times, it decides to enable the card randomly. It is so weird. It randomly enables sometimes like it has a mind of its own. I just bought vista for my laptop so i figured i'd install vista and hopefully my problem would go away. Sure enough the problem still happens after a fresh windows install. It is so frusrating. I hate that i have to restart the laptop like 15 times before the wireless card decides to enable itself. You guys have any clue on what's wrong? Is my wireless card messed up? When the card does enable itself though, it works fine so i am thinking that maybe i have a bad driver. I tried rolling back the driver but no success.

Posted On: September 19th, 2007, 04:11 PM . View Related Posts . . View 8 Replies .

Cannot Connect To Wireless Local Network

I can not connect to my wireless local network. I have internet access but i can not access the computers on our network. Why is that? I assumed virus is blocking my access, am i right?

Posted On: 2 months ago . View Related Posts . . View 2 Replies .

Wireless Setup - Unable To Locate An Access Point On Network

My main pc has 2 lan cards installed. 1st is a sis 900 pci card. 2nd is a realtek rtl8139/810x family fast ethernet nic. I connect to the internet via an ntl cable set-top box which is connected via lan to the realtek (a. K. A lan2 on my system), this is obviously setup fine as i am posting here . I have a linksys wap54g wireless-g access point connected to the sis900 card and the end objective is to connect it (wirelessly!) To another pc upstairs which has a linksys wireless lan pci card installed. But. When i insert the setup disc for the access point i cannot get any further than the fist page as i get. "The setup utility was unable to locate an access point on your network. Etc"

I know its plugged in fine & the lan cable is ok (i checked it with a laptop)

Posted On: March 14th 2005 . View Related Posts . . View 8 Replies .

Webcam For Hp Pavilion Dv6000

I'm just totally lost on how to take pictures and stuff on it. How do you upload the pictures from there. How do you find them on your documents. Is there any customizations you can do while taking pictures like (ex. Black and white, things like you can do on mac) does anyone know a link for like everything about the web cam?

Posted On: 1 month ago . View Related Posts . . View 1 Replies .

Hp Pavilion Dv6000 Not Connecting To Internet

Hp pavilion dv6000 not connecting to internet. When i try to connect to the internet on my laptop, the icon says "the dependency service or group failed to start" and then when i click diagnose, it says that windows can not resolve the problem. How can i get my laptop to connect to the internet?

Posted On: 2 months ago . View Related Posts . . View 2 Replies .

Hp Pavilion Dv6000 Support Windows 7 ?

Will an hp pavilion dv6000 support windows 7. ? Ive had this laptop since 2007 and im not sure if to upgrade to windows 7. Ive afraid some of the drivers will not work for windows 7. Im upgrading from windows vista.

Posted On: 3 weeks ago . View Related Posts . . View 2 Replies .

Hp Pavilion Dv6000 Webcam Not Working

Why is my hp webcam not working and is completely wiped out? My hp pavilion dv6000 laptop has built in webcam. It is a windows vista. The webcam has been working fine a few months ago but suddenly stopped working completely last month. I tried installing drivers and doing anything. The thing is when i try to search webcam nothing appears. I tried looking at the uninstalled drivers too but its not there. Please help, need this webcam to keep in touch with my parents who lives abroad and is too broke to buy a webcam.

Posted On: 3 months ago . View Related Posts . . View 1 Replies .

Hp Pavilion Dv6000 - Error - Memory Could Not Be Read

I am currently trying to install a recovery disk into my hp pavilion dv6000 and i got a message stating, (the instruction at 0x8000d030 referenced memory at 0x0012ac60. The memory could not be read. ) I am not really sure what this message really means, so could someone try to inform me on the meaning as simple as possible.

Posted On: 1 month ago . View Related Posts . . View 1 Replies .

Connect Hp Pavilion Dv6000 To Vizio Lcd

How do i connect hp pavilion dv6000 to vizio lcd? I bought monster vga cable but it doesn't work. My laptop rgb input doesn't have the two holes to lock it in. Answer:- the holes don't matter as long as the cable sits in there and once it is in there, go to the control panel and adjust your settings in the graphics card settings. If it gives the option, select the monitor as the output instead of the notebook, good luck.

Posted On: 6 months ago . View Related Posts . . View 1 Replies .

Hp Pavilion Dv6000 Isn't Turning On

Why isn't my hp pavilion dv6000 turning on? I was using my computer earlier and it just shut off. I noticed that when i have my power cord plugged into the computer, the charger light is only on for about 30 seconds and then it goes off. My computer will turn on while i'm holding the cord and getting a charge. When the charger is off my computer/lights turn on for 5 seconds then turn back off. Does it sound like my power source needs to be replaced?

Posted On: 1 month ago . View Related Posts . . View 5 Replies .

Restricting Access To Other Drives On Local Computer

I want to restrict drive access from them but not the use the internet. I've turned on the guest account and put a password for my account but now would now like to make my other hard drive invisible to them. Does anyone know how i can do this! I can them to be able to see drive c: in xp but nothing else! They keep smooping through all my picture, video and office files!

Posted On: September 11th, 2003, 06:42 AM . View Related Posts . . View 10 Replies .

Local Network Connection Cable Unplugged

I have win xp home edition and i recently had a problem start and i have no clue as to how to fix it. Last week my system started giving me the error that my "local network connection cable unplugged" and now i cannot get my network to connect. Here are the specs of my computer: amd xp 2200 cpu; biostar motherboard model: m7viq ver 1. 2 with via vt6103 lan chip; 768 pc2700 ddr memory. I run a vcom (system suite 5 utilities) firewall and virus checker. I have a broadband connection (motorola surfboard sb5100 cable modem) that runs through a 4 port router (network everywhere, linksys nr041). I have 3 computers networked through the same router and modem and no other computer has a problem with connecting to the internet, or to one another. Here are the attempts i have made to try and fix this problem but was unsuccessful (first i disabled the firewall and virus checker):

1. I've checked cable and it was plugged, tried a differnet connection on router and no success. Tried new cable, still not success. 2. I thought maybe a game my brother loaded (heavy gear ii) could have overwrote some important networking files since it is an online game, so i uninstalled the game. No success. 3. I tried 3 different restore points prior to the loading of the game and still no fix. 4. I ran xp's repair current windows utility and this still did not fix my network connection. 5. I've tried a different nic (realtek rtl8139/810x fast ehternet pci card) and it does the same thing as the onboard lan connection by giving me the same error. 6. When i go to the hardware manager, it says that both devices are working properly. 7. I pinged 127. 0. 0. 1 and nic checks out fine. 8. When i do a "ipconfig /all" at the command prompt, i get that both nic cards "media state" are disconnected. 9. I've done research on the internet on this problem and have not yet found an answer. I even went to heavy gear ii site and did not find anything that would help. I'm not even sure that the game caused the problem to begin with, but i'm out of guesses. I would like to go the windows update and run the updates on my system but i cannot get on the net to do so. I did load new drivers from a floppy for the realtek nic but that didn't work either. Can someone give me any suggestions on what to do next?

Posted On: July 26th, 2004, 09:15 PM . View Related Posts . . View 14 Replies .

Send Message To Computer In Local Network

How can i send a message to other computer in local network throw a command line? I try by my self and i found a command net send but i can't resume all parameters together in any way this the task:

Send a message to user ip 10. 0. 1. 54 as name mkc . A message (hi man !)

Posted On: March 17th 2008 . View Related Posts . . View 5 Replies .

Local Area Connection A Network Cable Is Unplugged

Local area connection. A network cable is unplugged? Everything on my computer is connected correctly but every couple of seconds my computer says pops up and says a network cable is unplugged. How do i fix this what does this mean could it be a virus?

Posted On: 1 month ago . View Related Posts . . View 1 Replies .

Connect Local Area Network ( Ethernet ) With Wan

Can we connect a local area network (ethernet) with wan? Suppose we want to connect a local area network (ethernet) with a wide area network, the question arises is, can we connect a local area network with wide area network?

If we directly connect the lan segment to the packet switch of the wide area network, then obviously every signal on the segment will be forwarded to the switch, to prevent this, can be use a bridge to connect this segment to the network switch (because bridge will only forward the packets if necessary)?

Another question arises is, every wan technology uses a specified frame format, suppose the wan is using a frame format that is different from ethernet frame format then what we will do?

Posted On: 2 months ago . View Related Posts . . View 1 Replies .

Connecting Wireless Gateway To Wireless Access Point

Connect a wireless gateway to a wireless access point. ? I have a actiontec gt724-wg router and a linksys wrt54g gateway. I want to use the linksys to get a connection to the actiontec wirelessly to run other computers in the house, including my ps2.

Posted On: 1 month ago . View Related Posts . . View 5 Replies .

Connecting Wireless Access Point To Wireless Bridge

Can i connect a wireless access point to a wireless bridge? How my network is set up right now. I live on a farm. We receive satellite internet at our neighbors house, and the internet is shot over to my house. They have a modem, router, and then bridge it over to my place. There is a router with another bridge halfway. Basically the whole farm is a wireless hotspot. Now the issue is i want to get a better connection in my house, right now it is low -> very low. -Would i be able to get a wireless bridge and connect a wireless access point to the bridge? I don't want to run cables all around my house. -Or can i just get an access point, i do not have a modem or router in my house though. The closest router is approximately 100ft away from my house. -What i want to do is set up an access point in my house. How can i do that without having any wired connection already in place? I know a wireless bridge receives a wireless connection and changes it to a wired connection, so can i run a ethernet cable from a wireless bridge to a wireless access point?

Posted On: 2 months ago . View Related Posts . . View 1 Replies .

360 Access Network Problem

Moved into a studio apartment part of a hotel complex for uni this year, the problem i am having is that i can't seem to get my 360 onto live, i think it has to do with the setup of the netowrk considring you have to log in on a html page to access the net (pops up when web browser opens). How do i get around this ? So far the only thought ive had is to somehow segregate my local network (router, 360, pc) and somehow connect the two diferent networks so that the hotel network thinks that my routers ip is the local ip that is logged onto their system.

Posted On: April 21st 2008 . View Related Posts . . View 4 Replies .

Cannot Access Network Connection Properties

This is is networked and is the admin. But it won't allow me to access the network connections properties. When i try to right click properties, the following is displayed. "You do not have sufficient privileges for accessing connection your admin. "

Posted On: July 24th 2005 . View Related Posts . . View 5 Replies .

Unidentified Network No Internet Access

I left the laptop on my desk and went to eat. When i got back i had the yellow triangle on my wireless internet connection saying "unidentified network, no internet access. " I spent a lot of my time trying to google the problem and nothing has worked yet. I even tried system restoring back to a few earlier dates and i still got the same problem. I've restarted my internet card, tried doing router delete 0. 0. 0. 0 on command prompt, tried changing it from public to home, but nothing. One thing i noticed was when i did a diagnose it told me this problem. (By the way i use windows 7, it sucks so bad i've been having so many problems with this program)
Here is what is says, "issue found" "wireless network connection2" doesn't have a valid ip configuration. It also said something about my "internet protocol version 4 and 6 (tcp/ipv4 and 6) i think it said no internet access to both of them can't exactly remember but it sounds like its linked to the first issue. If you have any idea how to fix the problem?

Posted On: 1 month ago . View Related Posts . . View 3 Replies .

Laptop Wont Connect To Internet, Wireless Or Local Area Connection

Last night, the wireless was fine, all connected. Then it randomly went off and wouldn't find any wireless network connections, but i just left it and went off. I went back on a few hours later, and it still wouldn't find any, even though other people could find them in our house. So i used a wire and connected to it and it was fine. Today when i went on, it still wouldn't find our wireless. So when i went to use the wire again, that wouldn't work either. It said i was working off-line, so i changed it to on-line, and it said it can't display the web-page, i really don't know what to do, but i need my internet.

Posted On: 2 months ago . View Related Posts . . View 3 Replies .

Cannot Access Printer Connected To Network Computer

Why can i not access a printer connected to another networked computer, even though i can access its documents? I have a desktop that has two printers connected to it via usb. The desktop is configured for network access, and is accessible by every computer in the house. I have three laptops with a wireless connection. All three can successfully connect to the desktop and see it's documents and connected printers. Only two of these three laptops can access the printer and print on it. The two laptops that can print have windows 7 and vista. The third laptop that cannot print has vista. It can see the desktop, it can connect to the desktop, it can see files, read files, and create files on the desktop. However, when i try to add the printer from the desktop to the list of printers on the laptop, it says access denied - however the other two laptops added the printer fine and can print without any trouble. Again, this one laptop that can't print seems to have full access to the desktops files. Any idea how to get this third laptop to add and send print jobs to the printer connected to the desktop "hub" computer? Because "add a new printer" button isn't working and continues to give me errors.

Posted On: 6 months ago . View Related Posts . . View 1 Replies .

Laptop Connects To Network With Limited Access

My laptop connects to my network with limited access and no internet connection how do i fix it? How do i fix it with out reinstalling os? Ps my os is vista.

Posted On: 2 months ago . View Related Posts . . View 2 Replies .

Unidentified Network - Laptop Won't Access Internet

My laptop connects to my wireless but it wont let me access the internet, its saying unidentified network. Like it connects but says no internet access and unidentified network i don't know why it saying that i tried on my roommate computer too, and his works just not mine. How do i fix it?

Posted On: 2 weeks ago . View Related Posts . . View 1 Replies .

Network Address Problem Connecting To Existing Wireless Network

Network address problem connecting new laptop to existing wireless network. Using a netgear dg834g router as the access point for 2 different pc's, which are not networked with each other, but both connect fine to the wireless network. Just got a new inspiron 6000. It recognizes the network and connects, but gives me an ip of , limited connectivity etc. Also no default gateway, or dns and wins server addresses. I know it should be giving me an ip of or something, i just can't figure out why it doesn't.

Posted On: May 18th 2005 . View Related Posts . . View 14 Replies .

Access Freenas From Wireless

I have been looking at and researching freenas for a while and finally built one. It was actually pretty simple, even though i made a few newb errors, i was able to research my problems and set it up. I know am able to access it and was able to map network drives to my windows 7 and xp systems. The problem i am having is that i cannot access the freenas box from any of my wireless computers. For example, my work laptop can access it when i am wired to the network, however, not wireless. Here is my setup:

D-link dgl-4100 wired router

I have an airlink 680 wireless router set up as an access point (dhcp turned off) to integrate wireless into my existing network. So, my d-link router is 192. 168. 0. 1

My airlink is 192. 168. 0. 250

My freenas box is 192. 168. 0. 240

Any computer is assigned by dhcp from the d-link. From the wireless computers, i am able to access the airlink, d-link and two network printers through their webgui. Not freenas. Cannot even ping from a command prompt. I have searched google and these forums and cannot seem to locate a solution. I suspect it may have something to do with static routing, however, i could be off base. I am sure there must be some simple way to fix this.

Posted On: 03-08-2010, 06:18 PM . View Related Posts . . View 19 Replies .

Wireless Internet Connection Only Have Limited Access

Why does my wireless internet connection only have limited access? For a while i have not been able to get internet connection unless i am connect manually, when i do try to connect it says i only have limited connection and i should try to reset my ip address or repair it but when i do that it says it's not able to? Can i fix this myself or do i have to go to a best buy or something?

Posted On: 3 weeks ago . View Related Posts . . View 1 Replies .

Wireless Ethernet Bridge Or Access Point?

Fundamentally, i'm trying to figure out the difference between a wireless ethernet bridge and access point. But here's what i want to do: i'm considering buying the ixps internet message clock, which needs a wired ethernet connection. I would like to move the ixps around to house, so i need a wireless connection. Here's the setup of my network right now: the cable modem is connected to a wireless router, which also has 4 wired ports. One of those wired ports is connected to a secondary router, which i had to configure to have a fixed ip or something like that so it would work. On that secondary 4-port router, i have connected a laptop, the ethernet cable from the main router, an external hard drive, and a printer. So i was wondering if a wireless ethernet bridge would do the trick by connecting one to the ixps. If i did that, would i need to add anything to the wireless router (like another ethernet bridge), or would the configuration work properly whereby the router can communicate with the ethernet bridge?

Posted On: 1 month ago . View Related Posts . . View 1 Replies .

Block Computers Access To Linksys Wireless Router

Ok, so like we are at the whole arp command area in my cisco class and i got me a question. When you do the arp -a command you get a list of hosts on the network and the mac addresses.could i use this information to block computers access to my linksys wireless router? And would/could it work on wireless users.

Posted On: January 8th 2006 . View Related Posts . . View 4 Replies .