Advertisements:




Samsung R451c Turn Off Silent Mode


How to turn off silent mode on a samsung r451c? I got a straight talk cell phone from wal-mart. I went to a movie and turned it on silent, i have no clue how i did it but it did. Now i've tried everything to turn it off silent mode, but i can't get it? The phone is straight talk samsung r451c.

View Full Post With 1 Replies

Related Forum Messages:

Please Follow Index to Quick Jump to the Message.


Sleep Mode Cannot Get Turn Back On

My compaq is in the sleep mode and i can't get it to turn back on. What can i do?

Answer:- unplug it from power. If it's a laptop, also remove the battery. Then hold down the power button for half a minute. Then put the battery back in and reconnect power, then press the power button - if that doesn't turn it on, try holding down the power button a long time again.


Posted On: 2 months ago . View Related Posts . . View 3 Replies .

Hp Nc6220 Laptop Doesnt Turn On With Battery Mode

My hp nc6220 laptop doesn't turn on with battery mode. ? My hp nc6220 laptop doesn't turn on with battery mode. If shows little fluctuation as i press power button and gets turn off immediately. But when i plug adopter and it works great on adopter mode. F
Note: i got checked the battery, it is in good health.


Posted On: 1 month ago . View Related Posts . . View 3 Replies .

Samsung Dlp 1080p Tv Unsupported Mode

Samsung dlp 1080p tv with ati radeon shows unsupported mode. I've connected my computer (graphics card: ati radeon x1650pro) through a vga cable to my tv, which supports 1080p. I've extended the desktop onto the tv. My screen refresh rate is 60hz. My drivers are all up to date. I setup my friend's 46" prima easily with 1080p mode, but in my tv the highest resolution i can get is 1280x960 (far from 1920x1080 at 60hz). If i go higher, the tv screen shows "unsupported mode". What can i do? Don't tell me to change the refresh rate or my tv doesn't support 1080p and such.

Posted On: 2 months ago . View Related Posts . . View 1 Replies .

Samsung Syncmaster B2330 Wont Turn On

My brand new samsung syncmaster b2330 will not turn on. I believe i have the correct driver installed, the cables have worked on other equipment, and it has a power source. It seems like it might have power, but it won't turn on. Is there some hidden button or is my monitor just defective.

Posted On: 1 month ago . View Related Posts . . View 1 Replies .

Samsung Syncmaster 971p Wont Turn On

I have the samsung syncmaster 971p and it wont turn on. The tower is working. What should i do?

Answer:-

First, check and reseat both ends of your video & power cable and make sure they are seated properly & fully. If that doesn't work, check your power indicator light and see what color, if any, it is. It should be green if the monitor is on. If it is green and you see no display, your monitor is probably bad. The backlight of inverter is bad and would need to be replaced. Otherwise, you can purchase a replacement. If the light is amber, then it's not getting a signal from the video card. Check and reseat the video card. Try booting into safe mode to see if you get a picture. If that doesn't work, then you may need a new video card. If safe mode works, then check your display settings in windows and change as needed. If there is no light when you push the power button, then the monitor is not getting power. Check your power cord and where it's plugged in at to make sure the power is good. If all that checks out, you will need to repair or replace the monitor.


Posted On: 5 months ago . View Related Posts . . View 1 Replies .

Silent Computer

I've been forced to listen to the lawnmower like noise of the fan attached to the heat sink of my xp1900 for two years, and i'm sick of it. I want a silent computer, or as silent as one can be, but i don't want to sacrifice power in the process. I know it's possible to make a powerful computer, but keep it quiet at the same time, and that is my goal. This seemed like the most relevant place to put a thread about building an entire computer, if not, just move it. Help, input, and comments appreciated.

Posted On: 07-21-2004, 10:32 PM . View Related Posts . . View 19 Replies .

Make My Computer As Silent As Possible

Okay guys here's the deal, my new rig is awesome, runs really well and all that shiz except coming from a laptop background i'm not used to the fan noise. Thus im' enlisting your help to make my case as quiet as possible while keeping it as cheap as possible. My case is the raidmax smilodon which i am insanely happy with, i did replace the stock raidmaz fans with silent x ones running at around 14dba i think. The main perpetrator for the noise is the front 120mm fan, any hints on how to make that less noisy would be handy to. I've rubber mounted all the fans as the silent x ones came with these nifty silicone screw thingos however it dind't really seems to make that make difference. So tehre you go guys, gimme all the tricks of the trade and little tips as to how to make my comp as silent as possible. P. S. Does acoustic dampening stuff you stick on this inside really work? Is it worth the money?

Posted On: 12-14-2006, 08:10 AM . View Related Posts . . View 2 Replies .

Quiet Or Silent Keyboard

My wife is "ruining my life" because my keyboard is waking her up, even though she is in the other room from my rig. Its a lenovo, non click. Im impressed with her hearing. Does anyone know of a truly silent keyboard? Advice much appreciated!

Posted On: 10-25-2009, 07:29 PM . View Related Posts . . View 10 Replies .

How To Make Hard Drive More Silent ?

I just got new seagate 250 gb sataii hard drive. Seagates have been usually pretty quiet. I can't say that this is noisy but it's noisier than other computer. What is the best and cheap way to reduce noise from hard disk? Or is there any? My case is antec sonata ii.

Posted On: 06-06-2006, 12:20 PM . View Related Posts . . View 8 Replies .

Sound Card Output Distorted And Silent

I accidentally plugged output of my integrated sound card to output( instead of auxiliary in) of my stereo. Sound is gone. On full volume i can hear sound, but it is very distorted and silent. Is it possible to fix it?

Sound card is sigmatel audio


Posted On: February 14th 2006 . View Related Posts . . View 6 Replies .

Fanless Or Completely Silent Water Cooling Units

Have any of you ever thought about building an absolutely silent pc. I think that would be really cool. There are silent psu options in the antec phantom500 and some thermaltake units, the nothbridges nowerdays are coming with heat pipes. Some gfx cards have no-fan heatsinks and you can buy some good fanless ones too you could get awaywith no case fans if you dont plan to oc at all but the stumbling block is always going to be the cpu cooler. Are there any fanless or completely silent water cooling units out there?

Posted On: 17-03-2007, 08:06 AM . View Related Posts . . View 3 Replies .

Would Asus Hd 4350 Silent Fit In Hp Pavillion Slimline ?

I'm planning on upgrading the graphics card on a hp pavillion slimline desktop, however my main wonder is whether or not getting a graphics card, asus 1gb - hd - 4350 silent: http://amzn. To/9hrhcn

For example; would it 'fit' as a replacement for the little intel built-in express graphics card?


Posted On: 3 weeks ago . View Related Posts . . View 3 Replies .

Play Gears Of War Game On Asus Eah4350 Silent

Can you play gears of war game on a asus eah4350 silent/di/1gd2 pci-e graphics card - 1gb?

Answer:-
However the asus hd4350 isn't that powerful. Even with the healthy 1gb of ddr3 memory its 800mhz memory clock and 64bit memory interface wont allow it to run this game at anything higher than 1024x768. It will run at 1280x1024 however it wont be playable and 1024x768 is a fully playable resolution

What i tend to do with demanding games like gears of war is tweak the detail and resolution settings, best thing to do is lower the resolution to 1024x768 and all detail settings to minimum/low then run the first chapter and check how playable the game is at those settings. If they are fine then slowly higher the detail and run again. You have several options open to you for example run at low resolution and higher detail or higher the resolution and stay with lower detail also run the frame rate utility "fraps"( http://www.Fraps.com/ ) which will allow you to monitor the frame rate at each settings

Bare in mind 25fps is a smooth and playable frame rate so use this as a reference rate, however 20fps can also be playable, it depends on the game.


Posted On: 2 months ago . View Related Posts . . View 2 Replies .

Computer Do Not Come Out Of Stand By Mode

I just started using stand by instead of leaving the computer active all night. Half the time when i went to activate the computer it would just shut off and or restart. I got better results oi got this computer about 3 years ago. Came with 120gb harddrive, 512mb ram, 250watt power supply. Since then i have added a second harddrive, and a firewire card, no problem [so long ago i did that].

Well lately theres been issues. I just started using stand by instead of leaving the computer active all night. Half the time when i went to activate the computer it would just shut off and or restart. I got better results of it not doing that by moving the mouse and hitting keys vigorously until my desktop came up, it not doing that by moving the mouse and hitting keys vigorously until my desktop came up.

But the last few days have been the worst. The green power light on the front is blinking, as usual on stand by, and i go start moving the mouse around, and eventually figure out, it wont come out of stand by. Eventually i figured out if i unplugged my dlink router, and then plugged it in again, it would reboot itself. Sometimes i couldn't turn the computer on without plugging in the router. It use to involve a lot of playing around with the router to get the computer out of standby and back on.


Posted On: June 1st, 2007, 12:09 AM . View Related Posts . . View 14 Replies .

Dual Mode Ram

I have 3 512mb ram : 1 with 320 mhz and 2 with 400 mhz. Currently i am using at 400mhz. Is it possible to set them up from single mode to dual mode channel?

Motherboard : intel 865perl


Posted On: May 12th, 2006, 12:48 PM . View Related Posts . . View 2 Replies .

No Boot From Safe Mode, Etc.

Computer turns on, screen shows bios screen, then options for safe mode, last known good config, etc. I've tried them all - best i've gotten so far is the winxp load screen, then screen goes to black and system hangs there. Anyone heard of this? I know it's not video card, because i get the initial winxp graphic w/blue bars running left to right and the flag. I'm not sure about the harddrive - in safe mode it shows all the dos stuff running down the screen, but then hangs. My plan is to burn a boot cd (no floppy drive installed in system) and try to troubleshoot from there. Either the startup routine in windows went bad, or it's a bad harddrive, or ?. I'll likely get to working on this over the weekend, but any input is appreciated.

Posted On: August 9th, 2005, 07:26 PM . View Related Posts . . View 6 Replies .

What Causes Pc To Boot In Safe Mode ?

Ok i just switched my pc on this morning and got the post screen for the 1st time ever. For the past couple of times , when i push the power on button, it would flash the led on the front and power back off. Then press it again and it fires right up. And today it boots in safe mode . I went into the bios and re loaded optimized defaults, and it is no longer in safe mode but it hangs a little longer right before going to the xp loading screen. At the bottom of the screen it says verifying dmi pool data, then it goes to xp loading screen. What could have caused it to boot this way in the first place. I have a new motherboard i am about to use anyway, but i just want to be sure i don't have some other problem.

Posted On: December 20th 2006 . View Related Posts . . View 5 Replies .

Monitor Keeps Going Off - Dpms Going To Off Mode

When i switch my computer on my monitor comes on and goes off again, before it goes off a box comes up saying dpms going to off mode, anyone tell me what this could be.

Posted On: March 16th 2005 . View Related Posts . . View 4 Replies .

Monitor Mode Not Supported

I have a samsung monitor and when i connect it to pc it says "mode not supported" with black background?

Answer:- your video adapter is currently set to a mode that the monitor cannot display. If it does not adjust itself automatically (many drivers will sense the mismatch and correct the problem automatically in a few seconds) set the display resolution to something that it can handle (1024 x 768 is almost always safe) and 60 hz refresh and connect it. Reboot and then go in and adjust the resolution to the monitor's native display resolution for the best performance.


Posted On: 2 months ago . View Related Posts . . View 1 Replies .

Sleep Mode Issue

So if i put my computer into sleep mode or it goes to sleep after an hour of idle time, when i hit enter to wake it the screen stays blank. The only way to wake it is to hit the power button. However if i do this the computer will intermittently turn on, as in the howl system lights up and then it turns off. It will continually complete this process until i flip the power switch on the back of the psu. Then when i hit the power switch once more, it will turn on and off and then finally boots. It sounds like a bios issue to me. I have sufficient power, even overclocked, otherwise i wouldn't be able to turn my computer on at all. Here are some relevant specs: mobo: gigabyte: ga-ep45-ud3p with award bios the most recent version and a 650 watt psu. This also seemed to happen after i had network adapter issues last night which also happened to be a bios issue, i fixed it by resetting to fail safe defaults. So it may have reset the option to allow sleep mode or something along those lines. Any suggestions?

Posted On: 2 months ago . View Related Posts . . View 2 Replies .

Computer In Standby Mode Never Came Back

I accidentally pressed the little moon key on the dynex keyboard connected to my desktop pc which although normally causes the pc to enter stand-by apparently means "commit suicide"! I saw a message that said the system was entering stand-by and i have as of yet been unable to get the machine to wake from it's slumber. I've completely powered off the system and disconnected the power cord and i've tried the cmos jumper trick as well. I can't even get a post screen with no thing plugged in but the video card and monitor!

I've removed the cmos battery and will let the system discharge over night so i'll post back in the morning, but any other suggestions would be appreciated! I have never encountered a case of a computer being this difficult to get out of standby, so i'm afraid the problem must run deeper than that.


Posted On: 14-04-2007, 09:20 AM . View Related Posts . . View 2 Replies .

Any Way To Use Serial Port In Safe Mode ?

I have an older ibm (thinkpad 500?) Using windows 2000 that crashes randomly. I only use this computer to run an automatic key machine in my truck that uses the serial com port. The computer runs fine in safe mode, but i can't link it to the key machine because the serial port is disabled in safe mode. Is there any way to enable the serial com port in safe mode?

Posted On: 14-05-2006, 04:35 AM . View Related Posts . . View 3 Replies .

Monitor Stuck In Standby Mode

My pc has run perfect for about 2 months now. But the other day i was on it and it suddenly crashed. I waited for a while but it still remained frozen. So i restarted it but there was no display on my mointor, it's like stuck in standby mode it's just stays on the orange light not the green. At first i thought it may of been the video card so i swapped it with a gforce 4 and still it stays in standby mode. It's not the monitor cause it's working fine with this pile of junk for a pc im having to use now. Anyone have any ideas whats causing this problem.

Posted On: 04-09-2005, 04:14 PM . View Related Posts . . View 7 Replies .

Dual Channel Memory Mode

I was wondering if anyone could help me with this issue. I have an (asus p5gd2x motherboard) with 4 memory dimm slots, i want to fill all slots with 1gb moduals = 4gb of ram, all of the same size and speed. In doing this, will all memory moduals then be running in dual channel mode? I'm doing the research but am new to the world of memory, any tips.

Posted On: November 20th, 2007, 04:50 PM . View Related Posts . . View 1 Replies .

Windows 98 Only Boots In Safe Mode

Windows 98 only boots in safe mode. When try to boot in regular mode it just sits at the clouds and the bottom progress bar keeps scrolling forever. No changes were made in either hardware or software. Just one day it stopped booting. It's driving me pretty crazy.

Posted On: 10-28-2006, 07:54 PM . View Related Posts . . View 3 Replies .

Display Working Only In Safe Mode

I have an older pc, intel ca810e board with onboard video. I just wiped the hard drive, and imaged it back with a known good image (win 2k), but now as soon as i enter the password to log on to windows, the video freaks out, like a hundred horizontal lines, i can see multiple mouse pointers all on same horizontal plane, basically i can't see enough to even tell it to shut down. When i boot into safe mode, all is well. I've flashed the bios, tried deleting the display adapter and rebooting, tried deleting the display adapter and reinstalling it from mobo driver cd (and from downloaded driver from web). All signs point to the onboard video being bad, but wanted to check with all of you to see if anyone had any other ideas. ?

Posted On: March 4th, 2005, 12:40 PM . View Related Posts . . View 5 Replies .

Low Power Mode While Downloading

Going from no computer to a computer raised my electric bill from $18/month to $40/month. Granted, some of that is due to me being in my apartment more often, and i don't play with no lights on either. But anyways, i'm trying to save money and have been afraid to leave my computer on for long periods of time while large files download. Going into sleep mode of course stops the downloads. My asus motherboard has a power-saving feature, and of course i turn off my monitor. Any other, relatively simple, steps i could take?

Posted On: 01-26-2009, 11:39 PM . View Related Posts . . View 5 Replies .

Screen Shaking In Window Mode

Brand new xfx 5770 running at stock settings runs fine in games, but when a game is in windowed mode it will shake the top of the screen unless i minimize everything but one window. If i play any game - such as warcraft 3, shattered horizon, tf2 - in windowed mode with a browser in the background or something then the screen will start shaking randomly. If anyone has a solution, let me know before i call up xfx.

Posted On: 01-05-2010, 10:06 PM . View Related Posts . . View 8 Replies .

Eyefinity In Portrait Mode Looks Like The Win ?

Pretzel on the wsgf posted an awesome review of his eyefinity setup with 3 - dellu2410's, and the games and movies in portrait mode looks like the winner. http://hardforum.com/showthread.php?T=1461837

- Already posted here in our own forums by pretzel. Let his thread get the looks please. I have been eyefinity gaming on my 3 - dell2408wfp's, and my biggest complaint has been the freaked out very stretched look in games. The 2 side monitors make games look like an acid trip almost, with the image completely too wide. But this portrait mode i might have to try out, it seems to look normal and very clear, almost perfect.


Posted On: 10-20-2009, 09:00 PM . View Related Posts . . View 4 Replies .